耐磨损,wear resistance
1)wear resistance耐磨损
1.High hardness andwear resistance coating JCW-B were deposited via arc spraying.采用电弧喷涂方法制备的高硬度耐磨损JCW-B涂层可广泛应用于工业零部件耐磨表面。
2.To endow thewear resistance to Ni-P-Cr/TiO_2 nanocomposite coatings, ZrO_2 nanoparticles was added to the basic bath.同时为了使制得的Ni-P-Cr/TiO_2纳米复合镀层具有一定的硬度和耐磨损性能,我们将纳米ZrO_2颗粒材料添加到镀液中,优化了电镀Ni-P-Cr/ TiO_2 ZrO_2双纳米粒子复合镀层的工艺参数,详细考察了各主要因素对镀层沉积速率,复合量,表面形貌的影响。
3.07 when tested in 6 600 minutes,and it was testified the coating has the durable property with low friction coefficient andwear resistance.07之间,显示了该涂层具有低摩擦、耐磨损和长寿命,并给出了其应用范围。
英文短句/例句
1.colour fastness to chafing耐磨擦色牢度,耐磨损色牢度
2.Resistant to wear, impact, salt water and aliphatic hydrocarbons.可耐磨损、碰撞，耐海水和脂肪烃类物质。
3.Valve body uses comol material,lt is corrosion resistant and wear and tear resistant.阀体材质络钼钢，耐腐蚀、耐磨损、经久耐用。
4.Grain-abrasion Behaviour of Wear-Resistant Steel BHARDY耐磨钢BHARDY的磨粒磨损行为
5.testing method for abrasion of vulcanized rubber (nbs method)硫化橡胶耐磨性能的测定(nbs磨损机)
6.testing method for abrasion resistance of textile fabrics: uniform abrasion method织物耐磨性试验方法：制服磨损法
7.testing method for abrasion resistance of textile fabrics: flexing and abrasion method植物耐磨性试验法：挠曲磨损法
8.Design and actualization of database of wear resistance materials耐磨料磨损材料数据库的设计与实现
9.Study of Wear Allowance on Anti-friction Layers of Shearer"s Sliding Shoes采煤机导向滑靴耐磨层磨损量的探讨
10.Solid-Liquid Two-Phase Flow Erosion Wear Properties of Si_3N_4-SiC CompositeSi_3N_4-SiC复相耐磨材料的冲蚀磨损性能
11.Wear,Material,Heat Treatment and Abrasion Resistance of Card Clothing针布磨损、材质、热处理和耐磨度的研究
12.Study on coating technology of wear and corrosion resistance for hydraulic turbine水轮机用耐磨蚀磨损涂层技术的研究
13.durability coefficient耐用系数（耐磨次数与强力损失之比）
14.Biomimetic Geometrical Structure Surfaces with Anti-abrasion Function and Their Abrasive Wear Against Soil;耐磨仿生几何结构表面及其土壤磨料磨损
15.Impact Abrasive Wear Resistance of New Type Martensitic Wear Resistant Steel新型马氏体耐磨钢的冲击磨料磨损性能
16.Abrasion resistant radial wear ring is standard on Model 6123 and smaller. Hardened SS Wear Rings optional on all models.耐磨的径向磨损环。配置在6123型号和更小的泵上。
17.Construction and implementation of database system of abrasive wear resistance materials耐磨料磨损材料数据库系统构成及实现
18.Influence of Copper on Abrasion Resistance of Wear-Resisting Casting Steel for Mines铜对矿山用耐磨铸钢抗腐蚀磨损性能的影响
相关短句/例句
Wear-resistance耐磨损
1.All of these are a reliable basis for output mechanism of zero tooth difference in wear-resistance design.针对零齿差齿轮输出机构的润滑状态及磨损判断等问题,首次将EHL理论应用于零齿差齿轮输出机构中并推导出计算公式,可以通过对零齿差齿轮输出机构的油膜厚度和膜厚比的计算,判断该输出机构的润滑状态及磨损程度;为零齿差齿轮输出机构的耐磨损设计提供了必要的理论依据。
2.All of these are a reliable basis for the planetary gear transmission in scraper conveyer in wear-resistance design.探讨了刮板输送机中行星齿轮传动的弹性流体动力润滑计算,并推导出相应的计算公式;分析了传动润滑状态与磨损的关系,为刮板输送机中行星齿轮传动的耐磨损设计提供了必要的理论依据。
3)abrasion resistance耐磨损
1.The hydraulic cylinders of hoists for the water works and hydropower projects usually operate in harsh and complicated environments and then the requirements on the corrosion andabrasion resistances are higher;however,the traditional technology for chrome-plating on the surface of the piston rod is not so perfect.水利水电工程中的液压启闭机油缸一般都处于较为恶劣和复杂的环境中,因此对其活塞杆的防腐蚀、耐磨损性能要求很高,而传统的活塞杆表面镀铬工艺效果并不理想。
4)antiwear["?ntiw??]抗磨损，耐磨
5)Wear Resistance耐磨损性
1.Effect of the carbon nanotube diameter on wear resistance of MWCNTs/PMMA composite system with four diameters was studied in this paper.研究了具有四种不同碳纳米管径的MWCNTs/PMMA复合物系的耐磨损性。
2.The effects of TiC particles on mechanical properties and wear resistance of 2A50 Al matrix were studied.研究了TiC对材料力学性能及耐磨损性能的影响。
3.Posterior composite resin is used to restore cavities involving stress bearing areas and is required to show high compressive strength,flexure strength, fracture toughness and wear resistance.后牙复合树脂(posterior composite resin)是指用于涉及到牙齿牙合面修复的材料,要求具有较高的抗压强度、弯曲强度、断裂韧性和耐磨损性。
6)durability rate耐磨损率
1.Using MINITAB software, the poly-linear regression equation for the main technological parameter viadurability rate has been built.使用MINITAB软件,建立了主要工艺参数对耐磨损率的多元线性回归方程,进行了回归分析,求得了绳锯耐磨损率较为精确的经验公式。
延伸阅读
光敏耐腐蚀耐电镀印料分子式：CAS号：性质：系指通过紫外光照射固化的一类抗蚀印料，分为:(1)耐腐蚀型，稀碱溶液去膜，能耐酸性腐蚀；溶剂去膜，能耐酸及碱腐蚀。(2)耐电镀抗蚀型，稀碱溶液去膜，耐酸性电镀液，溶剂去膜，耐弱碱性、酸性电镀液；(3)堵孔型印料，碱溶；(4)加强抗蚀型，去除型(耐化学镀铜)和永久覆盖型。由碱溶性感光高分子树脂、光敏引发剂、活性稀释剂、触变剂、流平剂、着色剂等组成。将上述组分在预混合器中进行搅拌混合，再经三辊机碾磨后配制成产品。无溶剂，无气味，不污染环境，很少有针孔。在印刷中黏度不变化，具有良好的丝网印刷性能。稀碱溶液去膜，能耐三氯化铁、氯化铜、过硫酸铵等酸性蚀刻，耐硫酸铜、铅锡合金及金银等酸性电镀液腐蚀。用于丝网图形蚀刻法和图形电镀法制造印制电路图形，也可用于化学蚀刻法制造精密的金属零件和图形。
